Mesa Tactical Sidemount 6-Shell Carrier for Remington 20-GA
SURESHELL® CARRIER FOR REMINGTON (6-SHELL, 20-GA)
Shell holder carriers are milled from 6061-T6 aircraft aluminum, then bead blasted and mil-spec hard anodized for a rugged non-glare finish. They are secured to application-specific brackets, and include high temperature adhesive-backed die-cut rubber gaskets to protect the host shotgun’s finish.
SureShell shotshell carriers are available in three configurations: four-shell, six-shell and eight-shell. The six-shell and eight-shell configurations can be installed on the left side of the receiver, while the four-shell carriers can be installed on either side of the receiver. Carriers can also be installed pointed back toward the stock.
The principle difference between one model of SureShell and another, aside from capacity, is the backing plate, which is designed to mount the carrier assembly on a particular model of shotgun. Side-mount SureShell shotshell carriers for Mossberg , Remington and Benelli M1 shotguns use the trigger group pin holes to secure the assemblies to the weapon; the Benelli M2 Tactical, Benelli M4/M1014, Benelli SuperNova Tactical and some Mossberg 500/590 versions take advantage of the factory-tapped rail mounting holes in the tops of these shotguns and include integrated Pictanny optics mounting rails; another version with an integrated rail is the saddle-mount design for Remington; SureShell Carriers for M4 SOPMOD stocks feature special hardware for attachment to these buttstocks; Adapter Mount SureShell shotshell carriers are designed to be attached to Mesa Tactical Telescoping Stock Adapter accessory mount points.
The following is a breakdown of the various components that make up the SureShell Aluminum Carrier system.
Aluminum SureShell Shotshell Carrier
SureShell shotshell carriers are assemblies comprising an aluminum yoke and backing plate and a Santoprene® elastomer tube. The yoke features four to eight vertical bores .700” or .810” in diameter to accept 20-gauge or 12-gauge shotgun shells. The shells are securely retained by the elastomer tube interfering with the bores. In many cases, shells can be confidently retained in a brass down as well as a brass up configuration, though brass up is most secure.
The elastomer used to interfere with the shell bores and thus retain the shells in the SureShell shotshell carrier is made of tough Santoprene thermoplastic. We are required to publish the following message to comply with California’s Proposition 65:
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
SureShell carriers are assembled at the factory with a black Santoprene elastomer tibe with a shore value, or stiffness, of A64. This has proven to be optimal for most customers and in most situations. However, some customers require a stiffer elastomer and for those operators we have included an alternative white elastomer tube with a shore value of A73. The black elastomer tube can be swapped for the white one if tighter shell retention is required.
The front trigger pin is replaced by custom Chicago screws instead of a standoff with 12 gauge Remington shotguns.
Several platforms use custom fasteners called Chicago screws. These are paired male and female fasteners that, when screwed together, meet at their respective shoulders for a precise fit on whatever platform they are made for (each shotgun platform will use different length Chicago screws). Ideally, when they are tightened against each other, they also secure the shell carrier without pinching the receiver. Two hex keys are provided for each screw size. Sometimes it is necessary to screw the fasteners in from both sides simultaneously.
*It is important to realize that once the Chicago screws are tightened against each other, they aren’t going to get any tighter, and applying too much torque will snap them at the center. It is useful to practice tightening them outside the shotgun before installation, to get a hang for how tight they can get, and also to clean the threads of any dirt or debris.
Adhesive-backed Rubber Gasket
The adhesive-backed rubber gasket material (not included with Saddle Rails or Saddle Mount SureShell assemblies) can optionally be used to keep the backplate screw heads away from the surface finish of your weapon.